• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a door hinge that is loose can be a doable job for the majority of homeowners. But, if the holes for screws are smashed and can't hold screws, you might need to put in wood glue and dowels before you can put back the hinge.

Before you do that though, brush away surface corrosion. This will help the dowels stay in place and give them a solid base to rest on.

Remove the Hinges

A variety of door hinges can be removed, making it easier to move the door from one end of the frame to the opposite side or remove the entire door if necessary. It is easy for anyone with a bit of patience, though you do have to know how to do it correctly.

If the hinges have been painted it is necessary to remove it before you attempt to remove the pins. If you don't, the paint will flake off and scratch the door when you attempt to lift it. To break the seal of the paint put the hinges into an stainless steel pan and fill the pan with water until the hinges are completely submerged. Let the hinges rest in the pan for 30 minutes. The heat from the water will soften the paint and make it easier to remove the pins.

Once the pins are loosened, you can remove the hinges from the frame and door. You can use a screwdriver to get the job done, but it is recommended to make use of a magnetic screwdriver for this task. This type of screwdriver is specifically designed to grab metal screws and will help you get the job completed much quicker.

Before you attempt to remove the hinges, it is recommended to spray them with grease. A simple lubricant will help you to speed up the process and also remove the pins and screws with ease. You can find this kind of lubricant in most hardware and home improvement stores.

You should also keep in mind that the number of hinges you'll need will vary depending on the kind of door and its settings. Heavier doors and solid-core doors will need more hinges, while hollow-core doors that weigh less might require just two or three.

It is also important to be aware of the various kinds of hinges in order to decide which one will best suit your needs. Exterior hinges are typically designed to support the weight of the door, while interior hinges will require to handle heavier loads.

Reattaching the Hinges

Over time, a door hinge can loosen and begin to sag or hang crookedly. It could be a huge problem, but the fix is usually simple. In most cases it's a simple tightening of the screw will fix the problem. However when the screw holes are stripped out, this can be more difficult. There is a trick to get the holes back in place that uses a wood dowel.

Begin by drilling the hole with a drill bit close to the size of the new screw (normally 3/8"). Fill in the hole with wood glue and a wooden stick. The dowel should be cut to a length the same as the screw to ensure a tight fit. Then, reinstall the screw and tighten it until the desired tightness. If the door continues to bind up, add another dowel into the gap. Repeat the procedure. Be sure to shut the door slowly in order to check the perimeter clearances after each adjustment.

You could also use a wood plug in place of the dowel. It's also possible, but may take some time to put in. Simply whittle a chunk of wood that is the right size for a snug fit, then press it into the hole. If you don't have a wooden tool you could also make use of toothpicks or wooden matches.

Once you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the head of the screw smaller so that it won't rub against the edge of the door when it is opened and closed. This will aid in tightening the screw prior to reinstalling the hinge.

After installing the hinge again, you should make sure to lubricate the hinge using a dry lubricant. This will prevent it from becoming stuck in the future. Products such as PB Blaster or Liquid Wrench are good alternatives. Apply a thin layer and allow it to soak into the hinge barrel for about 15 minutes.

Refinishing the hinges locks

If you're not ready to replace the hinges on your patio door hinge replacement (written by Botdb), you can do a few simple repairs. The first step is to check that the screws holding the hinge plate to the frame and door are tight. If they're loose, tighten them with the help of a screwdriver or a power drill. Be careful not too tighten the screws, because this can create gaps at the trim joints or worse, strip the threads.

If the problem is that the hinge plates are separated from the door and jamb it is possible to reattach the hinges by applying wood glue to the back of the plates and then inserting wooden dowels or toothpicks into the holes. Dowels and toothpicks create a solid foundation for the screws, preventing the plates from shifting when you drive them in. Let the glue dry before you can reattach your hinge.

The screws could also be smashed or gone. This can be corrected by replacing the screws. Make sure the drill bit is similar to the size of the screw hole to prevent drilling into the jamb or hinge.

Close the door once you've reattached the hinge and examine the gap between the frame and the door. The gap should be the thickness of a penny all around or less if the old door was not properly hung. This shouldn't be a problem as long as the hinges are correctly installed.

If you notice that the hinges remain loose, try adding a thicker hinge shim between the hinge plate and the mounting surface to give a little extra space. You can also take off the hinge pin and pound it down with a hammer to tighten it or use an entirely new hinge. It is also possible to lubricate the hinges using mineral or jojoba oil to lessen friction hinges uk and aid in holding their position. Regularly lubricating your hinges will aid in keeping them from becoming stiff or squeaky, and will also extend their life.

Cleaning the Hinges

The friction generated by the constant movement of a hinge attracts dust particles. These particles can become stuck and accumulate in the moving parts of door hinges if they're not regularly cleaned and lubricated. The hinge will become stiff and creaky and its appearance can rapidly change. Regular cleaning, lubrication, and inspection can help preserve the integrity of a hinge on a door and ensure its proper function.

Check the aluminium window hinges to see how much rust has accumulated on their surfaces. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace the hinges. If you can save the hinges, you can remove any loose rust with a steel wool and wire brush. Then, apply a rust remover from a commercial store or a homemade solution such as lemon juice on the hinge. Let the rust-removing solution remain on the hinges for several minutes in order to penetrate and dissolve any remaining rust.

If you don't wish to spend time and money to replace hinges, tightening the screws can bring back the hinge's functionality. It might be necessary, however, to add dowel or shim made of wood to the hinge when the screws have been stripped. Wooden dowels are round pieces of wood that are in the form of rods that are available in varying lengths and diameters. They can be purchased online, at woodworking supply stores and at home improvement stores.

You can also create an shim out of either plastic or metal, depending on the type of hinge you have. To make a dowel, cut a piece made of wooden dowel or another sturdy material to the desired size. You can then dip the dowel in carpenter's glue before inserting it into the cut hole and let the glue hold the dowel in the right position.

Before cleaning the hinges, lay down a paper cloth or towel to shield your flooring from spills. After the area has been secured and dry, clean the hinges with an absorbent sponge or a soft cloth that has been soaked in mild cleaner or vinegar to get rid of the build-up of dirt, grime and tarnish. You can use a toothbrush or small brush to get into difficult-to-reach areas in crevices and tight areas.