• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors are worn out over time and need to be replaced. When doing this it is important that the new handles match the exact dimensions of the handle that was previously used.

The top screw's location the lever, and the keyhole sizes are the three measurements that you need to determine. Refer to the size guide for assistance with this.

Inline Lever/Lever

A lever or lever door handle is a contemporary handle that can be used on new or replacement doors. This kind door handle is available in a wide range of designs and finishes. This handle is available from several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door changing window handles - voss-holmes-4.Thoughtlanes.net, are constructed of durable materials and are ideal for multi-point lock doors which require a robust design. The handles are inline and work from the same spindle and screw fixings, so they can be easily fitted to new or existing uPVC/Composite doors.

The handle can be adjusted and angled to fit the needs of all users. The handle has been tested to 200,000 cycles, which will ensure the quality of the finish as well as the performance of the handle over time. The sprung lever can also be cut to fit a wider range of locks. This is useful for narrower doors where the cylinder is situated further away from the door. A shortened lever is also an excellent option for doors where the latch can be operated by a thumb turn on the inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently than lever handles found on most doors. The handle can work off one single spindle (inline) or independently from both sides using two offset or inline spindles (pad). They are commonly utilized on UPVC doors with double glazing and come in a range of finishes and variations.

The handles are available in a variety of finishes including White Chrome, and Gold. The finish is BS EN 1670 Grade 5 and resistant to corrosion. This gives the handle a high performance and durability to serve its intended purpose.

All UPVC lever pads for handles for internal bifold doors include a spindle and screws and can be installed on the uPVC door. The backplate fixing centres of 211mm permit a bigger size of handle which can often be a benefit in replacing a defective or worn multi point door lock mechanism. The handle levers are sprung, solving the problem of handles that slide out of the horizontal position when not in use.

When selecting a replacement UPVC handle and spindle, it is crucial to match the PZ dimensions of the multipoint lock as well as the uPVC door. This measurement is also referred to as 'handle for patio door centres' or cylinder centres'. It is important to match the correct handles.

Once you have decided on the correct PZ size, you will need to ensure that the push and lever pads are shaped to fit the American with Disabilities Act compliant window handles for upvc that you need for your door. These are typically round or square with an internal lever and an external push pad.

Most of the UPVC lever pads that we offer are sprung, which means that they return to their horizontal position when not in use, rather than hanging out and possibly sticking in the frame. This prevents draughts from entering the home. The majority of UPVC lever pad handles come in both left and right handed versions which allows them to be placed on either side of doors.

Euro Cylinder

Cylinder locks are typically used on uPVC doors, but can be utilized on other types of doors. The cylinder lock is operated by a key which unlocks the cylinder's case. The case is then able to reveal pins that can be aligned to the pins in the lock, and permit them to rotate the revolving camera, thereby opening the door. Euro cylinders can be fitted with up to six pins. Doors that are internal and external require different levels of security.

The choice of cylinder is vital. It is based on the use that your doors and handles will receive. Doors that are external, for instance are required to be fitted with cylinders with greater security and doors inside can be secured with a standard cylinder. Certain cylinders come with extra features that increase security, for instance, anti-drill or anti-bump properties.

To make sure that the euro cylinder is of the right size for your door, it should be measured correctly. The cylinder should be measured from the central fixing screw hole to the other end of the cylinder, including the thumb turn if you have one. If you cannot measure using the lock in a fixed position, you can take it out of it. A cylinder that extends beyond the handle and escutcheon could be vulnerable to attacks, such as lock snapping, so it is crucial to make sure it's not too long.

Most modern cylinders are designed with anti-drill and bump resistance features that are built into their design. These features are designed to minimize the chances of an attack by forcing the cylinder to rotate in the opposite direction. This will help to deflect an attack and keep your door safe.

Certain cylinders are constructed to withstand snapping. This is a more frequent method of attack on cylinders where the break line inside the lock is targeted using a special tool to break off the front of the cylinder to allow the door to be opened. This is a much faster and more convenient method of gaining access than using a multipoint locking system. It also leaves less evidence of the break-in which could hinder insurance claims.

Spring Cassette

The spring cassette is situated in the base plate of the door handle. It provides a sprung solution to bring your multipoint lock handles to their original position after usage. There was a time when these types of handle did not have a spring built into them, and as a result, they tend to droop or 'drop' once the locking mechanism is removed. This simple part is the most effective way to solve this issue. It also helps prevent your door from getting stuck in the open or closed position as they are difficult to close manually.

These spring cassettes are specially made for use with sprung multipoint locks, they will not fit unsprung multipoint handles and you will require a hole specifically cut in the backplate to allow them to fit (please check the image for a technical diagram). They are a replacement for existing broken or missing cassettes in the backplate of the door handle for many brands of uPVC doors. They are sold as a single unit. They feature a square cut out that is able to accommodate an 8mm shaft.

These spring cassettes offer an excellent value solution for the problem of door handles that have become sagging. They are simple to put in and will increase the lifespan of your uPVC doors. For more information about our selection of uPVC accessories and spares, contact us today. in touch with our team. We are always ready to offer professional advice and assistance you.