• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change your door lock is a simple and inexpensive method to increase the security of your home. However, this procedure isn't for everyone. It requires a certain amount of skill and perseverance.

The cylinder is located within the knob's body. The cylinder is responsible to recognize the key when it is put into the lock.

Remove the old lock

First, remove the lock you have been using for a while. It's a simple process, but it is important to keep certain things in your mind. Make sure that the new lock fits your door. This will ensure that it fits snugly and doesn't create a gap around the deadbolt plug or latch.

After removing the latch plate, you will have to look for two bolts or screws in the casing's interior which are holding the casing in place with the lock halves. Take these screws off using a screwdriver before removing the lock out of the door. If you have a mortise locking mechanism there is an anchor screw that connects the handle to the spindle. Use a screwdriver to remove this screw, then remove the doorknobs.

Take the deadbolt and latch plug from the door jamb. Install your new lock. If you're replacing a mortise, you should measure the distance between the lock case and your door's edge to make sure that the new lock is a good fit.

You may want to replace your lock for a variety of reasons, such as the possibility that someone else is holding the key or if you have a new roommate. In any case, you can save money by taking the double glazing window locks repairs glazed double glazing window locks repairs lock repairs (read this post from Covolunteers) off yourself, rather than hiring an expert to remove it. The process is simpler than many people think, and it can be done in a few minutes.

Remove the trim and handle from your door. With a flat screwdriver, pry off the trim. You should be able to twist off most of it, and in certain cases the handles may fall off entirely. Next, examine the handle for a tiny pinhole on the inside and insert a straightened paper clip into it. This will trigger the release mechanism, which allows you to take off the handle. Then, look for a small tab in the interior of the lock and push it using a flat screwdriver. Once the spindle is removed, you can take off the housing and the cylinder.

Selecting a new locking system

When it comes time to pick a new lock, you have many choices. Look at different types of locks and select one that fits your door's style. Take into consideration the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole along the edge of the door frame). Choose a lock that fits the door thickness and the swing.

The majority of door locks are evaluated by BHMA and the American National Standards Institute to provide you with an idea of how well they are able to withstand the rigors of use and how difficult they are to disable or pick. A grade 3 lock might be a good choice for a tranquil urban apartment complex, whereas an entry grade lock could stand up to the traffic that is frequented by a storefront on a busy city street.

Most smart door locks require digital code to open. If you are concerned about hacking, or other security issues, talk to an expert locksmith.

Replacing the cylinder

If the cylinder of your door lock is broken window lock repair or damaged, you can replace it in just a few minutes with a simple do-it-yourself project. The key is to select the correct cylinder and follow the directions that accompany it. First, remove the handle or knob if it is present. Then, using a screwdriver, unscrew the trim that surrounds the lock cylinder. Once the trim has been removed, you will be able to access the screws that secure the cylinder and remove them with a flathead screwdriver. The cylinder can then be gently lifted out of the door.

Make sure you measure the length of your new cylinder prior to installing it. Find the distance from the center to the left and right sides of the cylinder using an instrument. Purchase a new cylinder that has the same measurements. This will prevent cylinders from snapping when doors are kicked or the key gets stuck inside.

Insert the replacement cylinder in the door, and then turn the key. This will align the cylinder with the carriage which is located usually on the outside of your lock. Then, loosen the set screws that should be just a couple of turns inside the head. If there is a screw located on the exterior of the case, which holds the door, you'll need to loosen it.

You can replace the cylinder that was used to lock your old lock with the new one by inserting it into the case, and tightening the set screws. Installing the part that connects the cylinder to an indicator stem for a lock is also important. This can be done by pulling three tabs on the back of the cylindrical with needle-nosed pliers. Attach the bracket that is smaller to the back of the cylinder. Then, you should put back in the strike plate and latch plate, as well as the retaining ring that is connected to the top of the lock cylinder.

Installing the new lock

If you're replacing an existing lock, you should start by measuring the width of your door. The majority of residential locksets are designed to fit a door thickness of 1 3/8 to 3/4 inch. If your door is thicker you will require a door kit that is thick and includes longer screws as well as an extended tail piece (for door knobs) or spindle extensions (for deadbolts).

Most locks come with a detailed instruction manual to guide you through the installation of the new hardware. Be sure to read the instructions thoroughly before beginning the process to ensure that you've followed all of the necessary steps. The manual will give you an idea of the amount of skill that is required to finish the task. You might want to ask a friend who has had experience in changing locks for help if you are changing locks for the first time.

It's a great idea cover the holes in the old lock before installing the new lock. This will prevent the screws from slipping through the holes, and also protect any tiles you have put in. It also shields your tiles from damage caused by dirt, rust and grime. SECURAM Touch comes with a strip of painter's tape that is intended to be used for this purpose, but you can also use gaffer's tape as well as masking tape if you have it available.

Once you've removed the screws that connect the interior portion of the lock section to the outside side then pull it out straight away. It's important to do this quickly so that the lock doesn't end up closing itself in a way that could end up damage the mechanism.

Install the new latch bolt in the upper cross bore of the new lock, if it comes with one. Be sure to put it in the right position as indicated by an illustration on the faceplate. Then, you can screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plate to the door jamb. Test the deadbolt by throwing it few times to ensure that it extends all the way into the strike plate and is fully secured. Follow the directions included in your electronic smart lock to program it. This involves downloading an application and registering your e-mail address, verifying your identity and connecting to the wireless network to connect your device.