• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Change a subaru impreza key Spare Key

When you lose your Subaru car key, contact a locksmith. Locksmiths can usually cut you a key cheaper than the dealer.

Subaru car keys are usually either smart "push-to-start" fob remote keys, or simply metal keys. The Fob key needs to have its chip programmed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your vehicle or the lift gate. These remotes use a keypad in your car to connect to your vehicle's computer.

Some models of Subaru come with a lesser-known feature called PIN Code Access. You can utilize a personalized number sequence to open and start your vehicle. Refer to the owner's manual for learn how to use this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

If your keys stop working, there's a good chance that the battery in the key fob is dying. The first thing to check is that the key fob has new batteries You can do this using a handheld remote tester or a basic multimeter that you can find in your garage at home.

The next step is to remove the key fob from its case, and then examine its transmitter circuit board. This will have one or two sets of eight-digit numbers, so write down the first set so that you will be able to remember it later. Once you've finished you can put the key fob back together and you'll be ready to begin programming it at home. The procedure for doing this is different based on the model and year of your vehicle but it's generally simple enough to complete by yourself.

Key Fobs

Subaru's latest models have key fobs that not only unlock doors, but also switch on lights, lock gas cap and even start the car. This last trick is particularly useful if been at a gas station and your car won't even start because the battery in the key subaru fob has gone out.

It is likely that your Subaru's key fob, whether it's brand new or old and can be replaced. It's important that you remember that models with high levels of technological sophistication may require a trip to the dealership. With a little time and effort, you'll get your replacement key fob in place at home.

Begin by opening the case and examining the circuit board of the transmitter. (Instructions on opening the case are usually included in the owner's guide). It should have two or three serial numbers each of which has 8 digits long. Write down the number that is the first in the series and save it for reference later.

Then, you'll need to get into the driver's seat and close the doors. Turn the key ten times to start your car, then switch it off. Press the lock button on your key fob, and then open the door. This will ensure whether your doors are operating properly. Then, close the door and take the key out of the ignition. The car should beep again, indicating that the key fob is programmed.

Ignition System

If your Subaru keys aren't functioning as they ought to, it could be due to the fact that the battery is dead. You can replace the battery in your key fob at home if you know how. The replacement battery is inexpensive and easy to locate. If your keypad doesn't respond to your commands, it may be a problem with it. It's recommended to visit a dealer to get an extra key. They can ensure that the key is genuine Subaru key, which is covered under warranty, and will be programmed for your vehicle. This is far more secure and less expensive than purchasing an aftermarket key from an organization online.

The dealer can also cut keys for you if you provide your VIN number and as proof of ownership. This information will be used to encode the key replacement to ensure that it can be accepted by your immobilizer. This process is more complex than cutting a new key, and the dealer will generally charge more for this service.

Once the new key is programmed, you are able to switch it over to the working key. It will take only five seconds to insert the new key, so keep your working key at your side. You can take the key off after the security light stopped flashing and you can test it.

Battery Replacement

subaru new key fobs are very useful since they can switch on the power windows and sunroof of your car with just a single button press. The battery in your subaru immobilizer key programming fob wasn't made to last forever, and will need to be replaced at some point. The good news is that replacing the battery is a simple procedure that you can do yourself with the help of this short guide from Capitol Subaru.

You'll need to locate the tiny crevice that divides the front from the back of your keyfob. Using a small flathead screwdriver, you can pop this seam wide to reveal a small compartment inside which is the battery. Install the new battery and make sure it is facing correctly. Remove the old one. Once everything is assembled, you can use your new key fob to lock or unlock your vehicle without difficulty!

It's always recommended to have an extra set of keys at hand particularly if you've lost yours or it's not functioning properly. A new key can be bought at your local dealership for cars or you can have one cut from locksmiths. It is essential that your key fob works well as soon as possible so that you can safely drive.