• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with an electronic keyless entry system built into. This key is similar to an remote control and can be exchanged with an lost kia key dealer.

Key fobs can stop working for a variety of reasons, such as the battery of the coin is dead, worn buttons signals, water damage, signal interference and a damaged receiver module. Here are some tips on how to get your Kia Sportage replacement key working again.

How to replace the remote key or smart key

The battery inside your Kia's smart key will eventually have to be replaced, regardless of whether it's a remote that starts with a push button or a regular key that does not contain a transponder. This is especially when the vehicle displays a message that indicates that the remote or smart key has a low battery.

It's a simple process. To replace the battery in the key fob, remove the mechanical key from the slit in the back of the key fob and break the cover. Inside the key fob, there will be an incredibly small screw that holds the battery in the correct position. Remove the old battery by detaching the screw with a small screwdriver. Then, you can insert the new kia key cost battery and close the slit inside the key fob.

Once the key fob has an updated battery Test it by pressing the lock and unlock buttons. If the doors lock and unlock in the same way, you're set! You can now take advantage of the Kia's hands-free lock/unlock feature whenever your fingers get chilly or you have to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a special programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of metal) do not require programming. If your key requires to be reprogrammed, you must know the key code number that is stamped on the key code tag and then record it in a safe location.

How to replace the battery

If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a signal that the battery should be replaced. A battery that is not functioning properly could cause other problems like the check engine light turning on or delayed cranking of the engine. Fortunately replacing the battery on the key fob is a relatively simple DIY task that requires only a few tools.

Before beginning the process, make sure that your vehicle is turned off and all doors are closed. Find the small, metal or plastic piece on the bottom of your key fob and jiggle it until a metal key is released. Then, you can insert this key into the driver's door handle to unlock your car.

To replace the key fob's battery, remove the cover from the back and use a plier bar tool to release the latch holding the black negative battery cable. Remove the old battery and orient the new one to ensure that the "+" positive side is facing you, while the "-" negative side is facing towards the fob's metal electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid bending or damaging the metal contacts.

Once the new battery has been installed, turn the key fob off and on in the ignition several times until the door locks cycle. You can then test your Kia key fob to check whether it's working again.

How do I replace a smart key

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The difference is that the smart key comes with an incredibly small key blade hidden within it, whereas the standard fob isn't equipped with. Both key fobs have an internal battery that will eventually require changing. It is a simple process that takes only two minutes.

Make sure you turn off your Kia and stand on a flat or well-lit surface prior to when you begin. Be aware that there are small parts inside the fob that can fall out if you are not vigilant.

The release button for the small size is located on the lower backside. It can be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been removed, you can remove the battery that was in it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After installation you should be able to lock or unlock your vehicle using your key fob, even if the engine isn't running!

How do you replace the mechanical key

The reprogram kia key fob keyfob is a great convenience, allowing us to lock or unlock our car simply by pressing the button. However, like all devices it may have issues from time to time. There are ways to address these issues and keep your key fobs working for an extended period of time.

A dead or weak battery is among the most frequent problems. This could cause the fob to stop working entirely or to work intermittently. If this is the case you should replace the battery an entirely new battery.

If this doesn't resolve the problem you can try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not to scratch any internal components or scratch the plastic. Once the battery is removed, replace it with a brand new one.

When the new battery is in, close and then open the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that will fit into the slot). Test the key fob and check that it's functioning properly. If the device isn't working, contact an expert locksmith or dealer to solve the problem. To avoid lockouts in the future, ensure that you have an emergency key that will work on all trunk and door cylinders.