• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Your first protection is your door lock. It will prevent unauthorized access to your home. Locks might require replacement because of signs of wear and tear or other events such as moving into a new house or a break-in.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will enable you to buy the right lock.

Deadbolt

If you want to make sure your door is secure against criminals, it's a great idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe it makes it harder for an intruder to break through the door. A single-cylinder deadbolt is activated with a key on the exterior and a thumb-turn device that is located inside. Deadbolts can only function when it is properly installed.

First, you'll need to find out if the door has a hole for deadbolts, or if it requires drilling. Utilizing the template included with the lock installation kit mark the location of the hole for the deadbolt on the door's surface. Use your tape measure to determine the height of the deadbolt. Mark this height on the door edge. Use speedsquares to draw a straight line across the mark that you made for the bolthole.

Then, using a power drill, bore out the hole until it is on the opposite side of the door. This could take a bit of time. Sand the hole and the edge of the door to smooth it. At this moment, it's a good idea also to stain or paint your door.

Remove any visible screws from the deadbolt. This will reveal the front and back assemblies of the deadbolt and also the internal bolt. Then unscrew the old bolt and replace it by the new bolt to match the door hardware. You will need to unscrew the bolt from the setplate. After this, you'll need to chisel the area on the door frame to accommodate the strike plate.

If your strike plate is not in alignment it could be because the previous installer did not mortise it properly, or a weatherstripping has changed the strike position. You will need to re-mortise your strike plate and possibly even the deadbolt itself to fix this issue. After this is done check the deadbolt by closing and locking it. Test the deadbolt by closing it and locking it once the bolt has been extended into the strike plate.

Knob

When a door knob is worn out, it can make your home or business less secure. It may make it more difficult to open or close the door, so it's a good idea to replace door lock [click through the next site] it. It shouldn't take longer than 30 minutes. You can use a screwdriver or pliers to remove the knob or handle that was previously used, but be careful not to damage any other parts on the door.

Spray WD-40, or a different dry lubricant on the mechanism of your door knob prior to you begin. This will let the new lock to slide smoothly when you turn it. It's essential to select the best knob and handle that matches your doors currently in order to ensure proper operation. If you don't already have a matching doorknob and Replace Door Lock handle, you'll need to buy a replacement.

To begin the replacement process, look at the knob or handle to see the screws that hold it in place. If there aren't any screws you can use a screwdriver to insert between the cover plate and the hidden screws plate and pop it off.

After you've removed the knob, check it for any signs of damage or rust. If the knob shows any scratches or marks, you'll have clean it. Otherwise it shouldn't require any major work.

Now is the time to put in the new one. Before you do that, look over the two new knobs to ensure you're selecting the correct one for your door. You'll need to choose one that has an extending rod that is designed to lock with the second knob's rod mechanism. Once you've put the new knob into the hole and then put it in the latch.

Thread the latch plate screws down and test the spring by pushing down on it several times. The latch should rise every time. Install the second knob and lock it to the rod mechanism of the first knob. Thread in the other long screws from the knob's interior through the hole in the cylinder of the doorknob on the outside and lock it in place.

Latch

A latch is a piece metal that extends into the door jamb to keep it shut. The latch is operated via a knob or handle on the interior of the door, or a thumb-turn on the outside. Deadbolts can be used to secure a latch and prevent intruders from breaking through the glass of the door. It can also protect against the accidental or deliberate closing by animals or children. You can install the latch using either a single-cylinder or double-cylinder deadbolt depending on the level you prefer for security.

Installing a deadbolt is the same as installing a latch, however, there are some distinctions. First, you must measure the setback of the doorjamb by using an instrument to make sure the new lock replacement upvc door will fit. The setback is the distance between the edge of the doorjamb cost to replace upvc door lock mechanism the middle of the hole that will be used for the latch faceplate. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If you have a larger setback, you may need to purchase a larger latch at a hardware store or locksmith.

Next, make a hole for a latch plate at the doorjamb's edge. Utilize a chisel to chisel the latch mortise. Make sure the hole's depth is enough to allow the faceplate to be flush with the doorjamb. Tape the strike plate in place to make sure it's placed correctly.

If the strike is too high, you could knock the door down or apply pressure using the tire iron or crowbar. This can cause cracks to the doorjamb. To correct this, the strike could be reduced by drilling a second hole through the doorjamb, and then chiseling out the core of the previous hole.

The last step is to put in the new strike plate, which is done by screwing it in place over the existing screw holes. Then apply wood putty to fill in the screw holes that were previously used and the bolt hole that is not used. Once the putty has dried, sand it to a smooth finish.

Strike

An electric strike is a metal piece where the deadbolt and latch engage when the french door lock replacement is shut. It is an essential part of the lock replacement upvc door's overall safety because it stops the door from opening and gives an additional level of resistance to force or kick. If a door is equipped with an electric strike, it can be opened with keys or the control unit that governs the electrical impulses.

Traditionally the installation of an electric strike involved cutting a section of the doorjamb in order to remotely remove a cylindrical lock's latchbolt from the pocket within the strike. This modification can be an inconvenience in regards to the aesthetics of an opening as well as exposing the latchbolt and keeper mechanism to unauthorized users.

Recently, a number of electric strike manufacturers have developed a new type of electric strike dubbed the "No Cut" strike that doesn't require a cutout in the doorjamb to function. The strikes use a unique design that allows the latchbolt and keeper to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike is equipped with an internal ramp that lifts the latchbolt and keeper whenever it receives a signal from a reader. The retracting of the keeper as well as latchbolt causes them to rise on the ramp, thereby locking the door. When the door is shut the deadbolt remains at a lower position and the latchbolt retracts into the keeper.

Installing an electronic strike is a simple procedure, particularly when you're replacing upvc door locks an older strike. If you are upgrading an existing access control system to an electric strike, you need to ensure that the new system is compatible. You will also have to make sure that the strike is properly connected to your access control system and is set up to operate in a safe manner.

One way to safeguard against unauthorized access is to upgrade the strike on your doors to a high-quality strike plate. These plates are fitted with four to six three-inch screws instead of the two, three-fourth inch screws commonly employed in regular strikes. The longer screws make breaking the frame to reach the piece that turns the thumb on a single cylinder deadbolt more difficult.