• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your cat go in and out whenever they want without having to let them in or out. They also prevent your cat from urinating inside the home.

It is simpler to install the cat flap on a Upvc panel than a glass one, but you will require some expertise and right tools.

Measure the Door

Fitting a cat door in a front door could be difficult, but provided that the cat flap is the correct one and you follow the directions you can make it less difficult. We will show how to trace the shape, use a jigsaw to cut out the door's area and then finish off the job by attaching the flap to the door. This will ensure that the flap remains in place and protects the door from wind and rain causing damage.

To determine the size of the cat flap that you need, Cat flap in upvc door panel measure the width of your pet. This will ensure that the flap is big enough to let your pet go inside and out of the house without having to open and close the door every time, but it is also small enough to keep them from going too far either way.

If your kit has an illustration of where to drill then you can stick it on the door and then draw a pencil around it. If your door has moulding or a sill at the bottom, make sure you leave plenty of space between your cat and the moulding or sill.

Next put on your eye protection as well as a dust mask. Then using a jigsaw, begin cutting along the line that you've drawn in, don't try to press the blade too hard, as this could make it cut faster than you want it to. Utilize a set square to ensure you are cutting the material correctly and that the cut is a rectangle shape. Once you are satisfied with the result, you can take the door material off.

Draw a Line

The cat flap allows you to let your pet go inside and out without worrying about unwanted visitors or unwanted gifts. It also prevents drafts and helps keep the temperature of your home stable. Fitting a cat flap to your door might seem difficult to those who haven't done it before. Many people call a professional carpenter or joiner to complete the job. This is a viable option, however you can do it yourself if the tools are right and the steps are adhered to.

This is much simpler to do on a wooden door, but it is still possible with uPVC. However, you must be careful not to scratch the doors because this will make it impossible to claim your warranty. The first step is to measure the door and ensure that it will fit the new cat flap. This isn't too difficult when you have the standard uPVC door, but you might need to take extra care if you are using a composite or other type of door as these are more difficult to cut than solid uPVC panels.

Next, you will need to determine the belly height of your cat. This is the height between the floor and the underside of your cat's stomach. You will need to locate a space on the door that allows your cat to pass through comfortably. Once you have the information, you'll have to mark the area with a spirit level and a pencil so you are certain that the hole will be suitable for your cat.

Once you've marked the area, it's time to cut the hole. It is essential to be patient and use a jigsaw ensure that the cuts are smooth and clean not uneven and rough. This could damage your door. Wear safety glasses and a dust mask when using a Jigsaw. Inhaling sawdust is dangerous for your health. After you've finished the cutting, you'll have to smooth out the edges of the hole using sandpaper, so that the cat flap can be fitted easily.

Cut a hole

It isn't easy to install a cat flap installer flap into a door panel or sealed double glazing unit. It is tempting to tackle the job yourself, but unless have experience with DIY, it's likely to be best to have an expert to complete the task for you. A botched job could not only be ugly, but also pose security risks. It could allow cold air to enter when the cat is outside and hot air to escape when it is inside.

The first thing you have to do is mark the position of the hole in the door using pencil and an ax level. This will ensure that it is placed and runs in a straight line with the other components of the door. Make sure to have sandpaper in your possession to smooth out any rough edges.

After the line is marked you should cut out the hole using a jigsaw. Be sure to wear the appropriate safety equipment for working with a power tool. If you're worried about noise, you can buy a cordless jigsaw which is quieter and easier.

You should only remove the material needed to make the cat flap. A little bit of extra material will be required for the thickness of the the flap but removing more than this can cause problems or cause damage to the door frame.

A upvc door may contain a metal frame or panel that could interfere with the microchip cat flap and if this is the case you will need to cut an oversize hole to ensure the metal does not come into contact with the wall of the cat flap, if this is done it is important to fill in the oversize gap and seal it with water.

If you're installing the cat flap in upvc Door panel flap onto the frame of a double glazed windows with a metal frame, you'll need to talk to a specialist who can provide you with a brand new glass pane that already has the hole for the cat flap premade inside. This will be cheaper than trying to install a cat flap inside an existing pane of glass that was not designed specifically for this purpose.

Install the Flap

Cat flaps allow your pet to come and go as they please, giving them the ability to unwind in the home whenever they're feeling like it. If you have an uPVC front door, it can be difficult to put in a cat flap. This is especially the case in the event that you don't own a glass panel which can be cut. Luckily, if you're happy to purchase and install a half-glazed replacement upvc door panels with cat flap uPVC panel then it is possible to fit a cat flap to these doors. It's not just a matter of drilling holes in the door. You'll also have to take a few steps to ensure that it is secure.

A composite, uPVC or GRP door panel is usually composed of a thin plastic skin which is bonded to an insulating polystyrene core. The material is quite fragile and care must be taken when cutting into it to avoid causing damage. This type of door typically includes a template which you can use as a reference to cut the hole in the door.

After you have carved out the hole in your front door, it is time to install the cat flap. You can pick from a wide range of designs, from simple push-button flaps to ones that are microchip-activated and allow your pet in. Whatever kind of cat flaps you select it's essential that your cat flap in bifold doors is able to use the flap comfortably without getting caught in the rain.

It's a good idea to opt for circular fittings instead of one that is square, since circles can be more securely cut into the door glass. It's because square holes are more likely to break the glass when drilled. It's also a safer choice to use since you're not putting yourself at risk by having to drill into toughened glass that may break and hurt your pet or your family. This is especially important if there are elderly or children in your home that could be hurt by glass fragments.