• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace upvc door lock mechanism Door Locks

Door locks are your primary line of defense against unauthorized access to your home. The locks may need to be replaced due to wear and tear or other events such as moving into a new home or a break-in.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will enable you to buy the right lock.

Deadbolt

Installing a deadbolt is a ideal way to secure your door from burglars. When the bolt is extended into the strike plate of the doorframe it makes it more difficult for an intruder through the door. A single-cylinder deadbolt can be activated with a key on the exterior, and a thumb-turn device located on the interior. Deadbolts can only function when it is properly installed.

First, you'll need to determine if the door has a hole for deadbolts, or if it requires drilling. Mark the location of the hole for the deadbolt on the surface of the door using the template that came with your lock installation set. Then, use the tape measure to determine the height the deadbolt should be. Mark this high point on the door's edge, and then use a speedsquare to draw a straight line across the mark you made to mark the bolt hole.

Then using the power drill, drill through the hole until it is on the opposite side of the door. This could take a bit of time. Then, sand the hole and the edge of the door until it is smooth. It's also a good idea to paint or stain the door at this point.

Remove any screws that are visible from the deadbolt. This will reveal both the front and rear assembly of the deadbolt and its internal bolt. Then unscrew the old bolt and replace it with an alternative bolt that matches the door hardware. The bolt is typically connected to a setplate which you'll need to unscrew. After that it is time to chisel the area for the strike plate on the door frame.

If your strike plate is misaligned, it's likely because the previous installer didn't properly mortise it or a weatherstripping was installed and changed the strike's position. To fix this problem, you will need to remortise both the strike plate and the deadbolt. Once this is completed, test the deadbolt by closing and locking it. Test the deadbolt by closing it and locking it after the bolt has been extended into the strike plate.

Knob

It can make your business and home less secure when the door knob is worn. It can also make opening or closing the door more difficult, which is why it's an ideal idea to replace door lock (click through the up coming article) it. It shouldn't take you longer than 30 minutes. Make use of pliers or a screwdriver to remove any knobs or handles. Be careful not to damage the other components of the door.

Before you begin, you'll want to spray WD-40 or a different dry lubricant onto the mechanism of the door knob. This will let the new lock slide smoothly as you turn it. It is essential to choose an excellent knob and handle that is compatible with your current doors to ensure that the lock is operating properly. If you don't already have a doorknob that is compatible then you'll have to purchase a replacement door lock.

To begin the replacement process, first look at the knob or handle to determine what screws hold it in place. If there are no screws then you can use the screwdriver to secure the cover plate between the screws plate hidden behind it.

After you have removed the knob take it apart and look for indications of damage and rust. If the knob is damaged or has scratches or marks then you'll need clean it. Otherwise it shouldn't require any major work.

Now it's time to install the new one. You must first study the two knobs to make sure that you've chosen the correct one for your door. You should select one with an extended rod that's designed to lock into the rod mechanism of the second knob. Once you've put the new knob in the hole and then put it in the latch.

Test the spring by pressing it down repeatedly. The latch should pop up every time. Install the second knob and secure it to the rod mechanism of the first knob. Attach the other long screws from the knob's interior through the hole in the cylinder of the exterior doorknob and secure it.

Latch

A latch is a piece metal that extends into the doorjamb to hold it closed. It is operated by a handle or knob on the inside of the door, or a thumb turn on the exterior side of the door. A deadbolt is a device used to secure a latch and replace door lock prevent intruders from breaking through the glass of the door. It also helps protect against intentional or accidental closing by children or animals. It is possible to install the latch using either a single-cylinder deadbolt, or a double-cylinder deadbolt depending on your preferred level of security.

Installing a latch requires the same steps like installing a deadbolt however, there are a few variations. To ensure that the new lock will fit first, measure the setback on the doorjamb using the tape measure. The setback is measured from the edge of the doorjamb up to the center of hole for the latch plate. A typical setback is 2 3/8 to 2 3/4 inches. If your setback is greater, you may need to purchase a latch that is larger from a hardware or locksmith store.

Next, make a hole for the latch plate into the doorjamb's edge. Utilize a chisel to cut the mortise of the latch. Make sure the depth is enough to allow the faceplate to be in line with the doorjamb. Tape the strikeplate to the doorjamb to ensure it's placed correctly.

If the strike is too high, you could kick the door in or apply pressure with the tire iron or crowbar. This could also cause cracks in the doorjamb. This can be repaired by drilling a new hole in the doorjamb, then removing the core from the old one.

Installing the new strike plate is the last step. This can be accomplished by screwing the new plate over the existing screwholes. Use wood putty then to fill in any existing bolt holes or screw holes which aren't going cost to replace upvc door lock mechanism be used. Once the putty has dried then sand it to an even finish.

Strike

The piece of metal that connects the latch and deadbolt when the door is closed is an electric strike. It is a vital component of a lock's overall security, since it seals the door and also provides additional resistance to force or kicking applied to the door. If a door is fitted with an electronic strike, it will be opened only with an entry key and a control unit that regulates the electrical impulses.

In the past, putting in an electronic strike required cutting off a part of a doorjamb in order to remove the latchbolt on a cylindrical lock from the pocket that is inside the strike. This modification is not only ugly, but also exposes the latchbolt mechanism and the keeper to intruders.

Recently, a number of electric strike makers have come up with an innovative type of electric strike, dubbed the "No Cut" strike that doesn't need cutouts in the doorjamb for operation. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without damaging the faceplate of the doorjamb.

The strike is equipped with an internal ramp that lifts the latchbolt and keeper when it receives an indication from the reader. The latchbolt and keeper are pushed higher up the ramp due to retraction. When the door is closed, the deadbolt remains retracted, and the latchbolt retracts into the keeper.

Installing an electric strike can be a simple process, especially in the case of replacing the strike on a previous door. However, if you're upgrading to an electric strike for an access control system, you will need to make sure your new system is compatible with the kind of lock you've installed. It is also necessary to ensure that the strike is connected to your access-control system and is set up to operate in a fail-safe way.

One way to safeguard against intrusions by thieves is to upgrade the strike on your doors to a high-quality strike plate. These plates can be fitted with up to six screws of three inches instead of the standard two screws of three-fourths inch. These screws are longer and make breaking the frame to reach the piece that turns the thumb on a single deadbolt cylinder more difficult.