• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace door lock Door Locks

Door locks are your first line of defense against unauthorized entry into your home. The locks may need to be replaced due to signs of wear and tear or other events like moving into a new residence or a break-in.

To begin, determine the size of your cylinder using the distance between the adjustment screw and the center of the knob lock cylinder. This measurement will assist you buy the lock that is right for you.

Deadbolt

Installing a deadbolt is excellent way to protect your door from burglars. When the bolt is extended into the strike plate of the doorframe, it makes it much more difficult for an intruder through the door. A single cylinder deadbolt can be activated with an exterior key on the side and a thumb turn device on the interior. Deadbolts will only work when it is properly installed.

First, you'll need to find out if the door has a hole to install deadbolts, or if it requires drilling. Utilizing the template included with the lock installation kit mark the location of the deadbolt hole on the door's surface. Use your tape measure to determine the height of the deadbolt. Mark this measurement on the door's edge, and then use speedsquares to draw a straight line across the mark you made to mark the bolt hole.

Next, use a power drill to drill this area until the hole is on the opposite side of the door. This may take a while. Then, sand grillandjoy.ru the hole and the edge of the door so that it is smooth. At this point, it's a good idea to paint or stain your door.

When the door is in place take off any screws visible on the deadbolt. This will reveal the front door lock replacement cost and back assemblies of the deadbolt as well as the internal bolt. Then, loosen the bolt and replace it with a new one that matches the french door lock replacement hardware. The bolt is typically connected to a set plate which you'll need to unbolt. Then, you'll need to chisel the area on the door frame for the strike plate.

If your strike plate is not aligned It's likely that the previous installer didn't correctly mortise it or a weatherstripping came along and changed the strike's position. To fix this problem it is necessary to remortise the strike plate as well as the deadbolt. Close and lock the deadbolt once you have completed this step. Make sure the bolt is extending into the strike plate and then test the key to make sure it is able to open and close smoothly.

Knob

It can make your home or business less secure when the door knob is worn. It can make opening or closing the door more difficult, so it is an ideal idea to replace the knob. It shouldn't take longer than 30 minutes. Use a screwdriver or pliers to remove any knobs or handles. Be cautious not to harm other components of the door.

Before you begin you'll need to spray WD-40 or a different dry lubricant on the mechanism of the knob on your door. This will let the new lock to slide smoothly when you turn it. To ensure that it operates properly it is important to select a knob and handle that match your existing doors. If you don't have a doorknob that is compatible, you will need to purchase a new one.

Before you begin replacing the knob, Till biografens hemsida examine the old knob to see what screws are that are holding it in place. If there aren't any screws, you can make use of a screwdriver and wedge it between the cover plate and the hidden screws plate and pop it off.

After taking the knob off examine it for indications of damage and rust. If the knob is damaged or has scratches or marks, you'll have clean it. Otherwise, it shouldn't require any major work.

Install the new knob. First, examine the new knobs to ensure that you're picking out the right one for your door. You'll need to choose one with an extending rod that will interlock with the rod mechanism of the second knob. Once you've put the new knob in the hole, slide it into the latch.

Test the spring by pressing it repeatedly. The latch should rise each time. Then, you can install the new knob and connect it to the rod mechanism of the first knob. Thread in the other long screws from the interior knob through the hole for the cylinder on the exterior doorknob and lock it in place.

Latch

A latch is a metal piece that extends into the door jamb to keep it closed. It is operated by a handle or knob on the interior side of the door or by a thumb turn on the exterior side of the door. Deadbolts can be used to secure a latch and keep burglars from piercing the glass of the door. It also helps protect against the accidental or deliberate closing by children or animals. A latch can be set with single cylinder deadbolts or double cylinder deadbolts according to the security level you prefer.

Installing a deadbolt is exactly the same as installing a latch however there are some differences. To make sure that the new lock will work first, determine the setback of the doorjamb with a tape measure. The setback is measured from the edge of the doorjamb up to the center of hole for the latch plate. A typical setback is 2 3/8 to 2 3/4 inches. If you have a higher setback, you may have to purchase a more substantial latch from a hardware store or locksmith.

The next step is to drill an edge bore hole through the doorjamb to accommodate the latch plate. Use a chisel for chiseling out the mortise of the latch and ensure it's deep enough to allow the faceplate of the new latch to be in a flush position with the doorjamb. Tape the strike plate in place to ensure that it's placed correctly.

If the strike is too high, you can push the door back or apply pressure using the tire iron or crowbar. This can also cause the doorjamb to crack. To fix this, the strike could be lowered by drilling another hole into the doorjamb and chiseling out the core of the old hole.

The last step is to install the new strike plate which is done by screwing it over the screw holes that are already in place. Then apply wood putty to cover the holes from the previous screws and the bolt hole that will not be used. After the putty has dried then sand it to a smooth finish.

Strike

The metal piece that engages the deadbolt and latch when the door is closed is an electric strike. It is a vital component of the overall security of a lock as it seals the upvc door replacement lock and provides extra resistance to force or kicks applied to the door. If a door comes with an electronic strike, it can be opened only by a key and the control unit that regulates the electrical impulses.

Traditionally the installation of an electric strike meant cutting out a portion of the doorjamb to remotely release the latchbolt of a cylindrical lock from the pocket of the strike. This is a drawback in regards to the appearance of openings as well as exposing the keeper mechanism and latchbolt to any unauthorised users.

Recently, several electric strikes manufacturers have created a "No Cut" kind of strike that does not require a cutout for operation. These strikes utilize a special design to allow the latchbolt and keeper to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike has an internal ramp that lifts the keeper and latchbolt when it receives an electrical signal from a controller or reader. The retracting of the keeper as well as latchbolt causes them to rise on the ramp, thereby locking the door. When the door is closed, the deadbolt remains retracted, and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy task, especially if you are replacing the strike on a previous door. If, however, you are upgrading to an electric strike to use with an access control system, you'll be required to ensure that the new system is compatible with the kind of lock you have installed. Also, you must ensure that the strike is properly wired to your access control system and that it is set up for fail-safe operation.

One way to safeguard against unauthorized access is to upgrade the strike on your doors to a high-quality strike plate. The plates utilize four to six three-inch screws instead of the two, three-fourth inch screws commonly used in regular strikes. These longer screws make breaking the frame to reach the thumb turn piece on a single cylinder deadbolt more difficult.