• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Lock (Postheaven.Net) Door Locks

The first protection is your door lock. It can stop unauthorised access into your home. The locks may need to be replaced due to wear and tear or other events like moving into a new home or a burglary.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the middle of the cylinder knob. This measurement will assist you select the appropriate lock.

Deadbolt

Installing a deadbolt is a great way to secure your door from burglars. When the bolt is extended into the strike plate of the doorframe, it makes it much more difficult for an intruder to break through the door. A single-cylinder deadbolt can be activated with a key on the outside and a thumb-turn piece situated inside. Deadbolts are only effective if it's installed correctly however.

The first step is to find out if the door has a hole to install a deadbolt or if it needs to be bored out. With the template included with the lock installation kit mark the spot of the deadbolt's hole on the door's surface. Utilize your tape measure to determine the height of the deadbolt. Then, mark this height on the edge of the door lock replacement. You can then use the speed square to draw an even line across the mark you made for the bolt hole.

Then using the power drill, drill out the hole until it is on the opposite side of the door. This may take some time. Sand the hole and edge of the door to make it smooth. At this moment, it's a good idea also to paint or stain your door.

Remove any screws that are visible from the deadbolt. This will reveal both the front and rear assembly of the deadbolt as well as its bolt inside. Then, loosen the bolt and replace it with a new bolt that matches your door hardware. You will need to unscrew the bolt from a setplate. After this is done then you need to chisel out the area for the strike plate on the door frame.

If your strike plate is out of alignment It could be due to the previous installer failed to mortise it correctly or a weatherstripping changed the strike's location. It is necessary to re-mortise the strike plate and possibly even the deadbolt to fix this issue. Once this is completed Test the deadbolt by closing it and locking it. Be sure the bolt is extending into the strike plate then test the key to ensure it is able to open and close easily.

Knob

When a door knob wears out, it can make your home or business less secure. It could make it difficult to open or close the door, so it's recommended to replace upvc door lock mechanism it. It shouldn't take longer than 30 minutes. Use a screwdriver or pliers to remove any knobs or handles. Be cautious not to scratch other components of the door.

Spray WD-40, or another dry lubricant on the mechanism of your door knob prior to you begin. This will allow the new lock slide effortlessly as you turn it. To ensure that it operates properly, it's important to choose a knob and handle that match the doors you already have. If you don't already have a doorknob that matches and handle, you'll need to buy a replacement.

To begin the replacement upvc door locks process, first look at the knob or handle to determine what screws are holding it in place. If there aren't any screws, you can use a screwdriver to wedge between the cover plate and the hidden screws plate and remove it.

After removing the old knob examine it for indications of damage and rust. If the knob shows any dents or marks, you'll have clean it. Otherwise, it shouldn't require any major work.

It's time to install the new knob. Before you do that, look over the new knobs to ensure you're selecting the correct one for your door. You'll need to choose one with an extended rod that's designed to lock into the rod mechanism of the second knob. After you've placed the new knob in the hole then slide it into the latch.

Thread the latch plate screws down and test the spring by pushing down repeatedly. The latch should rise every time. Install the second knob, and lock it to the rod mechanism of the first knob. Thread the long screws from the interior doorknob into the holes for cylinders on the exterior knob, and secure it in place.

Latch

A latch is a metallic piece that extends into the door jamb to keep it shut. The latch can be operated by a handle or knob on the interior of the door, or a thumb-turn on the outside. A deadbolt is a device used to secure a latch and stop burglars from piercing the glass of the door. It can also protect against the accidental or deliberate closing by animals or children. You can install the latch using either a single-cylinder deadbolt or double-cylinder deadbolt based on the level you prefer for security.

Installing a deadbolt is the same as installing a latch, however, there are some distinctions. First, measure the setback of the doorjamb by using a tape measure to be sure the new lock will fit. The setback is measured from the edge of the doorjamb up to the middle of the hole for the latch plate. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If you have a higher setback, Replace Door lock you may need to purchase a longer latch at a hardware store or locksmith.

The next step is to drill an edge bore hole in the doorjamb for the latch plate. Use a chisel to chisel out the latch mortise, making sure it's deep enough for the faceplate of the new latch to be in a flush position with the doorjamb. Tape the strikeplate in place to ensure it's placed properly.

If the strike is too high, you could kick the door in or apply pressure using a tire iron or crowbar. This can cause cracks to the doorjamb. To fix this issue, the strike can be lowered by drilling a new hole into the doorjamb and chiseling out the center of the hole that was previously drilled.

The last step is to put in the new strike plate, which can be accomplished by screwing it in place over the screw holes that are already in place. Utilize wood putty to fill in any old bolt holes or screw holes that aren't being used. After the putty has dried you can sand it down to give it a an elegant finish.

Strike

An electric strike is a metal part where the deadbolt and latch are engaged when the door is closed. It is a vital part of the lock's overall security, as it prevents the door from opening and provides an additional barrier to force or kicking. If a door replace door lock is equipped with an electronic strike, it will be opened only with keys and the control unit that regulates its electrical impulses.

Traditionally, installing an electric strike required cutting out a portion of the doorjamb in order to remotely release a cylindrical lock's latchbolt from the pocket within the strike. This is an inconvenience when it comes to the aesthetics of an opening as well as exposing the keeper mechanism and latchbolt to any unauthorised users.

Recently, a number of electric strike manufacturers have come up with a "No Cut" kind of strike that does not require a cutout for operation. The strikes use a unique design to allow the latchbolt and keeper to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike has an internal ramp that raises the latchbolt and keeper whenever it receives an electrical impulse from a controller or reader. The retraction of the keeper and latchbolt causes them to rise on the ramp, which locks the door. When the door is closed the deadbolt remains in extended and the latchbolt is retracted into the keeper.

Installing an electronic strike is a straightforward procedure, especially when you're replacing an older strike. If you are upgrading an existing access control system to an electric strike, you need to make sure that the new system is compatible. Also, you must ensure that the strike is connected to your access control system and that it is configured for fail-safe operation.

Upgrade your strike plates to heavy duty strike plates to stop the entry of unauthorized persons. The plates are made of up to six screws of three inches instead of the standard two screws of three-fourths of an inch. The longer screws make it more difficult for people to break the frame and then reach inside to turn the thumb turn piece of a single cylinder deadbolt.