• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

boarding up windows service Up Windows and Doors Before a Storm Hits

Before a storm hits, boarding up your windows and doors can protect your home from damage. You'll require a few items to do this.

First, take measurements of the window's height and width including the framing (not the surrounding trim or masonry). Write these measurements down to ensure you don't forget them.

Preparation

It is best to cover your doors and windows before the occurrence of a natural or stormy weather. This will minimize property damage and reduce the chance of a fatality. It takes lots of planning to board up windows. You must purchase and measure plywood boards and you need to know the exact dimensions of each window. Additionally, it takes time to cut the boards and then install them correctly. The process can be streamlined by beginning the preparations as soon you hear about an approaching storm. You can avoid stress at the last minute and make it easier for both you and your employees.

Begin by listening to weather forecasters and boarding Up windows And Doors following the guidelines set by your local government. The earlier you begin the process the better, since it gives you enough time to collect and store the required items without being pushed by a storm that is rapidly approaching. Depending on the severity of the pending storm, you might require massive quantities of plywood to cover all of your windows. To ensure you get the correct size, use a tape measure to determine the width and height of each window opening. Make sure you consider the framing or trim around each window as and any sills with extended extensions when applicable.

Then, determine the size of the plywood sheets you require by dividing your window's total width and height by 2. If your window measures a width of 16 inches, the thickness of each sheet is 8 inches. If you have a wood exterior, drill pilot holes in the plywood sheet to align with the window frame underneath to avoid splitting when screwing in the screws.

To make sure that the window's opening is larger than what one sheet of plywood can accommodate, cut two separate sheets that are each half the size of the intended window and place them side-by-side on the wall. Cut a piece of 2 by 4 in (5.1 10.2 cm) 10.2 cm) of lumber to the length the connecting edge between the two sheets of plywood, and place it on the top of the seam. Then, screw 2.25 in (5.7cm) screws into the plywood sheet and into the bracing to join the two.

Materials

To ensure security and safety for security and safety, boarding up windows and doors should be done using only sturdy materials that will not break under pressure or split in high winds. Plywood is the most common material used to encase windows. It is simple to use, inexpensive, and easily available. Select plywood that is exterior grade (CDX) since it is stronger and will have less knots and warps. Storm shutters, also known as hurricane shutters, are more durable options. They can be put in over windows that are already in place and offer greater protection against broken glasses and weather conditions that can be severe.

Once you've identified the location of the window openings, you can measure the height and the width to determine the amount of plywood you'll require. Then, use a power drill to create pilot holes into the plywood sheets at 2-inch intervals around each window. Before attaching the plywood, you must identify and mark the locations of studs on the wall to ensure the boards will be fastened securely. If you have wood siding on your property, search for nailheads to determine the stud position. Otherwise, you can probe for stud positions using your drill. Drive the screws into the framing, not the sheathing or trim. A plywood panel attached only to these materials can become a safety hazard in strong winds.

If the size of your window is too large for a single sheet of plywood, cut two pieces that are each the size you require. join them together with 2 by 4 inch lumber. Label each plywood sheet so you know what window it will be covering.

Make sure you use corrosion-resistant screws that are long enough to penetrate the sheathing and the studs to secure the plywood panels to your wall. Try to drive the screws into the studs so that they are half as deep as the thickness of the plywood but be careful not to go too deep and damage the underlying structure of your house.

In addition to securing your windows, you should also put up an "No Trespassing" sign on the property, and consider installing polycarbonate security glass like DefenseLite over your windows. These transparent shields bond over the existing glass to guard your windows and doors and are virtually indestructible, preventing criminals from breaking in.

Installation

If you reside or plan to move to an area that is prone to hurricanes and are worried about the threat of storms, it's best to board up your doors and windows. It's a project that can be accomplished quickly and effectively, but only if you take the time to measure and cut your plywood before the storm comes.

You'll also require a few other tools, like a drill (or an hammer and nails in the event that you don't have a power drill) and tape, a saw gloves, a level and a pair of safety glasses. It's also a good idea for the plywood to be coated with sealant in order to make it waterproof.

Start by taking measurements of the width and height of each window opening, then cutting your plywood sheets so they fit inside the frames with a 4-inch overlap on all sides. It is best to do this on-site, as it gives you more control over the precise dimensions of the plywood.

Cut the boards to the desired size using a track or circular saw. Once they're installed it is necessary to sand down all of them. Once your boards are in place then screw the 3" stainless hanger screws made of steel into the framing posts around each window. Use washers on each bolt and wings nuts to ensure they are secured. Make sure that each screw penetrates the studs by at least 2 inches to ensure that the board is strong enough to resist high winds.

If you are building with concrete blocks, you can join the plywood with galvanized pan head screws which are driven into the edges of the panels into bricks or cinder blocks. You'll also have to drill pilot holes in the masonry and then insert corrosion-resistant screws into the holes. This project can take three hours for each time period. It is crucial to start the work as soon when an alert for hurricanes has been issued. This will allow you enough time to complete the task prior to the time when the storm is expected to hit.

Maintenance

You should be prepared to secure your doors and windows before an extreme storm. This will help you to avoid costly repairs and protect your home from further damage that could be caused by wind, rain, flying objects and other factors.

Having the right materials can make the boarding up houses up process much easier and quicker to complete. It is crucial to measure each window precisely. This will ensure that the plywood or OSB fits snugly and won't fall off easily. If you're using plywood, ensure that you are using exterior-grade sheets and think about adding an extra layer of protection.

Once you have the plywood or OSB measured, mark the areas where screws will be inserted into the board. Then, use a drill to pre-drill holes in the plywood at intervals of 12 inches. This will allow you to safely fix the boards using hanger bolts during a disaster or emergency situation. When the storm has passed and the local authorities have given the all-clear, take out the bolts but keep them in case of a need in the future.

The next step is to put the plywood panels over the windows. This is a two-person job, so be prepared before you start. If you're using plywood make sure to sand down the edges to ensure they're smooth and won't scratch your paint or trim. Then, use corrosion-resistant screws to join the plywood with the pilot holes. If your home has vinyl shingles on it, nail the plywood directly to the shingles, and not to the wood framing.

A boarded-up window can also be used to discourage burglars. Burglars are more likely attack a building that has a locked or broken window. Also, they are more likely to break in the store with a boarded up window boarding up near me than one that has no. If you're a retail business owner, this is something you should take seriously.