• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace a lock on a upvc door to replace door lock (for beginners) Door Locks

The first protection is your door lock. It can stop unauthorised entry to your home. Locks might require replacement because of signs of wear and tear, or other situations like moving into a new home or a burglary.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the middle of the knob lock cylinder. This measurement will assist you purchase the right-sized lock.

Deadbolt

Installing a deadbolt can be a great way to secure your door from intruders. When the bolt is extended into the strike plate of the doorframe, it makes it harder for an intruder to get through the door. A single-cylinder deadbolt is activated using a key on the outside and a thumb-turn piece that is located inside. A deadbolt will only work if it is installed correctly.

It is first necessary to find out if the door has a hole that is suitable for a deadbolt, or if you need to bore it out. With the template included with the lock installation kit, mark the location of the deadbolt hole on the door's surface. Use a tape measure to determine the height of the deadbolt. Mark this height on the door edge and use the speedsquare to draw a straightline across the mark you made to mark the bolt hole.

Then, use a power drill to drill this area until the hole reaches the opposite side of the door. This may take a while. Sand the hole and the edge of the door to smooth it. At this point, it's a good idea to paint or stain your door.

Remove any visible screws from the deadbolt. This will reveal the front and back assemblies of the deadbolt and also the bolt that is inside. Then, remove the bolt and replace it with a brand new one that matches the door hardware. You will need to unscrew the bolt from the setplate. After this is done, you will need to chisel out the area for the strike plate on the door frame.

If your strike plate is not in alignment, it could be because the previous installer failed to mortise it correctly or [Redirect-Refresh-0] a weatherstripping changed the strike's location. It is necessary to re-mortise the strikeplate and possibly even the deadbolt to correct this problem. Close and lock the deadbolt after you have completed this step. Make sure that the bolt is extending into the strike plate and then test the key to make sure it opens and closes easily.

Knob

When a door knob is damaged, it can make your business or home less secure. It can also make opening and closing the door more difficult, which is why it's recommended to replace it. replacing a upvc door lock knobs is an simple DIY project that shouldn't take more than 30 minutes to complete. You can use a screwdriver or pliers to remove the knob or handle, but be careful not to scratch any other parts on the door.

Spray WD-40, or another dry lubricant, on the mechanism of your door knob prior to you begin. This will help the lock to move smoothly when you turn it. It's essential to select the best knob and handle that is compatible with the doors you currently have to ensure that the lock is operating properly. If you don't have a match you'll need to purchase a replacement doorknob and latch plate.

To begin the replacement process, first look at the knob or handle to determine what screws hold it in place. If there aren't any screws, you can use a screwdriver to insert between the cover plate and the hidden screws plate and then remove it.

After you have removed the knob, inspect it for indications of damage and rust. It's important to clean it off if there are any scratches or marks however, you shouldn't need to do anything when the knob is in good shape.

Install the new knob. You must first study the two knobs to ensure that you are choosing the correct one for your door. You'll need to select one with an extending rod that is interlocked with the rod mechanism of the second knob. After you've placed the new knob into the hole and then put it in the latch.

Test the spring by pressing down on it repeatedly. The latch should spring back up every time. Next, install the other new knob and lock it to the rod mechanism of the first knob. Thread the long screws of the interior doorknob into the cylinder holes on the exterior knob and fix it in its place.

Latch

A latch is a piece metal that extends through the doorjamb to hold it shut. The latch is operated via a knob or handle on the inside of the door, or by a thumb-turn on the exterior. A latch can be secured using deadbolts to stop intrusions from piercing the glass. It also helps protect against intentional or accidental closing by children or animals. A latch can be set using a single cylinder deadbolt or double cylinder deadbolts according to the security level you prefer.

Installing a latch involves the same steps like installing a deadbolt but there are a few distinctions. First, measure the setback of the doorjamb by using a tape measure to make sure that the new lock will fit. The setback is the distance from the edge of the doorjamb, to the center of the hole to accommodate the latch faceplate. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If your setback is higher than that, you might need to purchase a latch that is larger from a locksmith or hardware store.

Next, drill a hole for the latch plate at the doorjamb's edge. Utilize a chisel to chisel the latch mortise. Make sure the depth is sufficient for the faceplate to be in line with the doorjamb. Place the strike plate in place to ensure that it's in the right position.

If the strike is too high, [Redirect Only] you could push the door back or apply pressure with a tire iron or crowbar. This can also crack the doorjamb. To fix this, the strike can be lowered by drilling a new hole through the doorjamb, and then chiseling out the core of the hole that was previously drilled.

Installing the new strike plate is the final step. This can be done by screwing the new plate over the existing screwholes. Then, use wood putty to cover the holes from the previous screws and the bolt hole that won't be used. After the putty is dry, sand it to an even finish.

Strike

An electric strike is the metallic part where the latch and deadbolt engage when the door is closed. It is an essential component of the lock's overall safety, as it prevents the door from opening and gives an additional barrier to force or kicking. If a door is equipped with an electric strike, it can only be opened by a key or the control unit which controls the electrical impulses.

In the past, putting in an electronic strike was as simple as cutting a portion of a doorjamb, which would remove the latchbolt on a cylindrical lock from the pocket inside the strike. This modification can be a drawback when it comes to the appearance of an opening, and it also exposes the latchbolt and keeper mechanism to unauthorized users.

Recently, several electric strike manufacturers have developed a new type of electric strike called the "No Cut" strike that doesn't need an opening in the doorjamb to function. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike has an internal ramp which lifts the latchbolt and keeper when it receives the signal of a reader. The latchbolt and keeper are pushed higher on the ramp thanks to the retract. When the door is closed the deadbolt remains in extended and the latchbolt is retracted into the keeper.

Installing an electric strike can be an easy process, particularly if you are replacing upvc door lock mechanism an existing strike door. However, if you are upgrading to an electric strike for an access control system, you'll need to make sure your new system is compatible with the model of lock you've installed. You will also need to make sure that the strike is properly wired to your access control system and is configured for fail-safe operation.

Upgrade your strike plates with heavy duty strike plates to stop unauthorized entry. These plates are fitted with four to six three-inch screws instead of the two three-fourth inch screws typically used in regular strikes. These screws are longer and make breaking the frame to reach the piece that turns the thumb on a single deadbolt for a cylinder more difficult.