• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About Boarding Up a Door

Boarding up a door is one method to shield vacant investment properties from the elements. It may not prevent all damages but it can assist to avoid some of the issues that are associated with severe storms.

The boarding up and burglary repairs of doors and windows will also deter trespassers and vandals. However, it can be expensive and time-consuming to set up plywood boards over the openings on a house boarding up service.

Measure the Door

The first thing you'll require is a tape measure. You may want to keep a chair or ladder nearby in case you need a better view of the top of the frame. If you need to make use of these tools, be sure to wear gloves and goggles.

Begin by taking measurements of the length of the door. This can be done by running a tape measure horizontally along the door. Be sure to eliminate any other door components, such as a door sweep and door sweep, from this measurement. Then, measure the height by measuring from the floor to the existing sill plate or the lintel. It is important to take measurements in several places, particularly when measuring doors older than they might not be an exact rectangular shape. If the measurements differ, use the largest figure.

After you've logged the width and height measurements and you'll need to determine what size boarding you'll need to fit into the frame. Ideally, it should be 2'' greater than the door's width and 1 2'' higher. This will allow you enough room to shim both the door and frame into place.

It's a great idea to remove the trim or casing around the jambs of the door to see the studs. This will enable you to determine the exact distance between the frame's studs and the edge.

Once you've removed the trim, Boarding up a door you'll be able to measure the width of the frame of the door by running the tape across the entire frame in three places and using the smallest measurement as the width of your door. You should also determine the height of the frame from the top to bottom on both sides, and use the shortest measurement as the height of your door.

If you're having issues with these measurements It's a good idea to speak with an expert and ask them to come to your home to take the measurements for you. They will be able to tell you exactly what kind of door and size you need and how to prepare the frame to accommodate the new door.

Cut the Plywood

A door frame is generally comprised of a set of thin boards or studs that create a hollow space around the door. Two hinges are connected to the studs and keep the door in place. If you want to finish a door, you will have to take it off its hinges overnight. To prevent insects from entering your home and to secure the door's opening, a simple method of boarding up services a door involves placing plywood inside the opening. This is easy to do without having to screw or nail the plywood to the door frame.

Plywood is simple to work with, cheap and looks stunning when completed. This makes it the ideal material to provide an interim solution to problems that require the removal of an existing door while renovating or installing a brand new one. It can also be useful to secure the opening in the room being renovated, such as an unfinished basement, or a construction site.

For a wall constructed of plywood begin by measuring the width and height of the door opening. Note the measurements using an utility knife and a metal straight edge, such as a drywall or a metal square. Then, snap the chalkline along each line to indicate where to cut. Use a circular blade to cut the plywood to size.

When cutting the plywood, it is essential to protect your ears and eyes. If possible wear eye protection and earplugs as you are working. It is also essential to use a blade with lots of teeth which will permit you to cut quickly and without any tear-out. Use a small piece of wood to guide the blade. Hold it a hair's width away from the mark when cutting.

Fastening a pair of short braces to each end is a good way to secure the plywood in place without screwing it into studs. Put one of the braces on the side of the door, and the one on the outside. Install a deck screws in each hole and tighten using an open-end ratchet.

Fasten the Plywood

It's time to attach the frame to the panel once you have the plywood sheet cut to the right size and the holes for the rails and stiles of the door frame predrilled. It is a fairly straightforward project that does not require a lot of carpentry expertise, provided you follow the correct procedure and use the right tools.

Begin by setting up a table near the doorway with two sawhorses and 2-by-4 framing lumber at each end of the table. Lay the entire sheet of plywood flat on top the sawhorses and use the marks made during the measurement process as a reference for cutting. Mark the lines using an utility knife and a drywall square or another metal straight edge. This will serve as a guide for the saw blade, and will help prevent splintering when you cut the plywood.

Wear eye protection and use a circular table saw equipped with a fine-toothed blade cut along the score line. Then sand the edges of the plywood panel with 120-grit sandpaper. This will smooth the panels and remove any burrs from the saw cuts. After sanding process, apply a coat of wood sealer to the plywood panels and allow to dry as directed by the manufacturer.

Install the hinges on the door frame. If you're using a hinge with a T-hinge drill holes on the outside edge of your door to allow for boarding up a door the strap portion of the hinges. Then, attach the outside hinge to the frame with a screwdriver. Repeat the procedure on the inside of the door for the remaining hinges, being careful not to overtighten any of them, or the door will shift.

If you're using a single outside T-hinged door, you can make it easier to close and lock using a chain latch by putting a piece wire through the loops on the outside hinges. Fold a piece of make a half-way tie, and then thread it through the two holes on the exterior of the door. Then, twist the wires and lock the door.

Install the Plywood

Using the measurements you took using the measurements you took, put the plywood in the door opening. Shim the header (top) of the frame and the sill (bottom). Utilize a level and ensure that there's no slop between the sill and the header. If the level isn't quite right, place another shim where necessary and continue the process until the header and sill are even.

Once the plywood is inside the frame, fix it with stainless steel hinge bolts and wings nuts. It's a good idea make use of a screw gun with a hex-head attachment to avoid stripping the head of the screws.

If your house has studs running the length of your doorway, you could drill hanger bolts into each framing member. This is a far easier task than drilling the hole with a drill or drywall saw.

After putting the plywood in place, measure the width and height of your door opening. If needed, trim the bottom plywood to fit the height of your door frame. Cut two pieces of framing lumber 1-by-6 to serve as braces for the upper and lower ends. Cut along the lines that are marked on your plywood using circular blades with fine-toothed teeth. Wear eye protection. Remove any splinters from the cuts with a sanding block.

Once you've got the braces set attach each one to the plywood with pairs of finishing nails 2 inches long. Counter sink all nail heads after you've finished. The braces should be sealed with a good wood sealing product, like the wipe-on polyurethane from Minwax.

If the door is too big it is possible to add decorative molding to fill in the space between your door and jamb or you can reduce the size of your opening. In most cases it's cheaper and easier to simply buy an entirely new door. It also solves any issues you might have encountered with your door's original model, if it was damaged or was not fit for the opening.