• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up Windows and Doors Before a Storm Hits

The act of boarding up service near me up your doors and windows prior to the storm hits can offer measurable protection against damage. You will need a few items to do this.

First, en.sulseam.com measure the window's width and height, including the framing (not the trim around it or masonry). Note these measurements so you won't forget.

Preparation

It is recommended to put up a board up your doors and windows before the occurrence of a natural or stormy weather. This will stop property damage and reduce the loss of life. boarding up and burglary repairs up windows requires lots of preparation, like buying and measuring plywood boards as well as determining the exact dimensions of each window to cover. It takes time to cut and install the boards properly. It is possible to speed up the process by preparing the boards immediately you hear of an approaching storm. By doing this you will avoid a stressful last minute rush and make the process much simpler for you and your staff.

Begin by listening to weather forecasters and following the guidelines provided by your local government. The earlier you begin the process the better, as it allows you plenty of time to collect and store the required items without being pushed by a fast-approaching storm. You may require a substantial amount of plywood to cover your windows depending on the severity and intensity of the storm. To ensure you get the right size, you can make use of a tape measure to determine the width and height of each window opening. Make sure to include the trim or framing around each window, and any ledges that are extended, if appropriate.

Next, calculate the dimensions of the plywood sheets you need by dividing the total window height and width by 2. For example, if the width of your window is 16 inches, the thickness of each sheet should be 8 inches. If you have an exterior made of wood, you should drill pilot holes in the plywood sheet and align them with the window frame underneath to avoid splitting when screwing into the screws.

If you have a bigger window opening than one sheet of plywood is able to handle cut two sheets of plywood which are each half large as the desired window. Place them side-by-side on the wall. Then cut a piece 2 by 4 inches (5.1 by 10.2 cm) lumber to the length of the connecting edges of the sheets of plywood and lay it over the seam. Then, drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them together.

Materials

To ensure security and safety ensure safety and security, use only materials that are durable and won't break or shatter in high winds. Plywood is the most commonly used material to board up windows. It is simple to use, inexpensive, and readily available. Choose plywood that is exterior grade (CDX) because it will be stronger and have fewer knots and warps. A more durable option is hurricane or storm shutters, which are put up over existing windows to provide greater protection against shattered glass and weather conditions that can be severe.

Once you've identified the location of your window openings, measure the width and height of each one to determine how much plywood you'll need. Use a power drill to drill pilot holes into the sheets of plywood around each window at intervals of two inches. Before attaching the plywood, determine and mark the stud locations on the wall to ensure that the boards are anchored securely. If your home has wood siding, search for nailheads that could indicate stud locations. If not, you can look for stud locations using your drill. Screws should be driven into the framing, not into the sheathing or trim. A plywood panel that is attached to these materials may become a safety hazard in the event of strong winds.

If the size of your window is too large for a single sheet of plywood, cut two pieces which are each half the size you require and join them together with 2 by 4 inch lumber. Label each plywood piece so that you can identify which window it will be covering.

Make sure you use corrosion-resistant screws that are long enough to penetrate the sheathing and the studs to secure the plywood panels to your wall. To attach the plywood panels to the wall, use screws made of corrosion-resistant that are long enough to penetrate both the sheathing as well as the studs.

In addition to securing your windows, it is also advisable to place a "No Trespassing" sign on the property and think about installing polycarbonate security glazing like DefenseLite over your windows. These transparent shields are bonded to existing glass and shield your windows and door. They are virtually unbreakable and discourage burglars from breaking into the house.

Installation

If you live in a region susceptible to hurricanes, or plan to move to one, the best option is to secure your doors and windows before the possibility of a storm is afoot. This project can be done quickly and effectively however only if you take the time to measure and cut, then label your plywood before the storm hits.

You'll require other tools as well which include a drill, a saw (or an hammer that has nails if you do not have the power tool) and the level, gloves and safety glasses. It is a good idea to apply sealant to the plywood and make it waterproof.

Begin by measuring the window's width and height. Then cut the plywood sheets to fit inside the frames. It is recommended to cut the sheets on the spot, as it gives you more control over the precise dimensions of the plywood.

Use a circular saw or track saw to cut the boards to the proper size, and remember that you'll need to sand them down after they're put in. Once you've put your boards in place, screw 3 inch stainless steel hanger bolts into the framing studs around each window. Use washers to secure each bolt and wing nuts. Make sure that every screw penetrates at least 2 inches into the studs, to ensure that the 24 hour boarding up service near me is sturdy enough to withstand strong winds.

If you're building with concrete blocks, you can attach the plywood to the building using galvanized pan-head screws driven through the overlapping edges of each piece into cinder blocks or masonry blocks. You'll also need to make pilot holes in the masonry, and then screw corrosion-resistant screws through the holes. This project can take anywhere from three to four hours per window, which is why it's essential to begin the process when you learn that a hurricane watch has been issued. This will give you enough time to complete the project before the storm arrives.

Maintenance

It is recommended to secure your doors and windows before an extreme storm. This can help you avoid costly repairs and also protect your property from further damage from wind, rain, flying debris and other factors that can impact the windows.

The right tools will make the commercial boarding up service-up process much easier and quicker to complete. The key is to precisely take measurements of the dimensions of the windows you must cover. This will ensure that the OSB or plywood is fitted snugly, and that it will not be able to slide off easily. If you are using plywood, be sure to use sheets made of exterior grade, and consider adding a protective finish.

Mark the locations where the screws will need to be put into the board after you have taken measurements of the plywood or OSB. Then, you can use a drill to pre-drill holes in the plywood at intervals of 12 inches. You can then use hanger bolts to secure the boards in an emergency or disaster situation. After the storm is over and the local authorities have given you the all-clear, remove the bolts, but save them in case of a need in the future.

The next step is to place the plywood panels on top of the windows. This is a two-person job So, be prepared prior to starting. If you're using wood, make sure to sand down the edges so they are smooth and won't scratch paint or trim. Then, nail the plywood to the frame using screws that are corrosion-resistant and fit into the pilot holes. If your home is lined with vinyl shingles it is best to attach the plywood to the shingles, not the wood framing beneath.

A window that is boarded up can be used to deter burglars. Burglars will target a building with a damaged window or one that's not locked. Also, they are more likely to break in the store with a boarded up window than one that has no. This is something that retail business owners should take very seriously.