• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door lock Door Locks

Door locks are the first line of defense against unauthorized access to your home. The signs of wear and tear, as well as instances like moving into a new house or burglaries, could trigger the necessity of replacing your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will enable you to purchase the correct-sized lock.

Deadbolt

If you want to ensure your door is safe from burglars, it's a good idea to install deadbolts. The bolt extends into the strike plate that is on the door frame when it's locked, making it more difficult for a burglar to gain entry through the door. A single-cylinder deadbolt is activated by a key located on the exterior, and a thumb-turn device that is located inside. A deadbolt will only work if it's installed correctly however.

First, you will need to find out if the door has a hole for deadbolts, or replace door Lock if it has to be bored. Utilizing the template included with your lock installation kit, mark the location of the deadbolt hole on the door's surface. Then, you can use your tape measure to determine the height the deadbolt needs to be. Mark this high point on the door's edge. Use the speedsquare to draw a straight line across the mark you made to mark the bolt hole.

Then, using a power drill, bore through the hole until it reaches the opposite side of the door. This could take a bit of time. Then, sand the hole and the edges of the door until it is smooth. At this point, it's a good idea also to stain or paint your door.

Remove any screws that are visible from the deadbolt. This will reveal the front and back assemblies of the deadbolt, as well as the bolt that is inside. Then, unscrew the bolt and replace it with a brand new one that matches the door hardware. You'll need to remove the bolt from a setplate. After that, you'll have to chisel the door frame to accommodate the strike plate.

If your strike plate is misaligned, it's likely because the previous installer didn't properly mortise it or a weatherstripping popped up and changed the strike position. You will need to re-mortise the strike plate and perhaps even the deadbolt to fix the issue. Close and lock the deadbolt once you have completed this step. Be sure the bolt is extending into the strike plate then test the key to ensure it closes and opens smoothly.

Knob

It can make your home and business less secure when the door knob is damaged. It may make it more difficult to open or close the french door lock replacement, which is why it's a good idea to replace lock in upvc door it. It shouldn't take you more than 30 minutes. You can use a screwdriver as well as pliers to remove the old knob or handle However, be careful not to scratch any of the other components on the door.

Before starting you'll need to spray WD-40 or a different dry lubricant onto the mechanism of the knob on your door. This will help the new lock slide smoothly as you turn it. It's essential to select a quality knob and handle that matches the doors you currently have to ensure that the lock is operating properly. If you don't have a doorknob that matches and handle, you'll need to purchase a replacement.

To begin the replacement upvc door locks process, look over the knob or handle to determine what screws hold it in place. If there aren't any screws, you can use a screwdriver to insert between the cover plate and the hidden screws plate and pop it off.

After you've removed your old knob, examine it for signs of rust or damage. You'll have to scrub it off if you notice any scratches or dents, but you shouldn't have to do anything major If the knob is in good condition.

Install the new knob. Before you do that, look over the two new knobs to ensure that you're picking out the right one for your door. You'll need to choose one with an extending rod that is designed to lock with the rod mechanism on the second knob. After you've inserted the new knob in the hole then slide it into the latch.

Thread the latch plate screws down, then test the spring by pressing down several times. The latch should rise every time. Install the second knob, and lock it to the rod mechanism of the first knob. Thread the long screws from the interior doorknob through the holes for cylinders on the exterior knob and fix it in its place.

Latch

A latch is a steel piece that extends out into the doorjamb to keep it closed. It is operated by a handle or knob on the interior side of the door or a thumb turn on the exterior side of the door. A latch can be secured by deadbolts to stop thieves from breaking through the glass of the door. It also offers protection from accidental or intentional closing of the door by pets or children. You can choose to install an entry point with either a single-cylinder deadbolt or double-cylinder deadbolt, depending on the level you prefer for security.

Installing a deadbolt is exactly the same as installing a latch, but there are some differences. To ensure that the new lock will work first, you must determine the setback of the doorjamb with an instrument such as a tape measure. The setback is measured from the edge of doorjamb all the way to the center of hole for the latch plate. The standard setback is 2 3/8 to 2. 3/4 inches. If your setback is higher it is possible to purchase an extra-long latch from a hardware or locksmith store.

Next, drill a hole for the latch plate at the edge of the doorjamb. Use a chisel for replace door lock chiseling out the mortise of the latch and ensure it's deep enough for the faceplate of the new latch to be close to the doorjamb. Put the strike plate into the correct position to ensure it's in the right position.

If the strike is too high, you could push the door back or apply pressure with the tire iron or crowbar. This could cause the doorjamb to break. To fix this, the strike can be lowered by drilling another hole in the doorjamb and chiseling out the center of the hole that was previously drilled.

Installing the new strike plate is the final step. This can be done by fixing the new plate to the existing screw holes. Use wood putty then to fill in any old holes for screws or bolts that aren't being used. Once the putty is dry then sand it to a smooth finish for professional results.

Strike

An electric strike is a metal piece where the deadbolt and latch are engaged when the door is closed. It is a crucial component of the overall security of a lock since it keeps the door shut and offers additional resistance to kicking or force applied to the door. If a door has been equipped with an electric strike, it can be opened with keys or the control unit that controls the electrical impulses.

Traditionally the installation of an electric strike meant cutting a section of the doorjamb to release the latchbolt of a circular lock from the pocket in the strike. This modification is not only unattractive, but also exposes the latchbolt mechanism and keeper to unauthorized users.

Recently, several electric strikes manufacturers have developed a "No Cut" kind of strike that doesn't require a cutout to operate. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without causing damage to the faceplate of the doorjamb.

The strike is fitted with an internal ramp which lifts the latchbolt as well as the keeper when it receives an indication from the reader. The retraction of the keeper and latchbolt raises them on the ramp, which locks the door. When the door is closed, the deadbolt remains retracted, and the latchbolt retracts into the keeper.

Installing an electric strike is an easy task, especially if you are replacing an existing strike door. If you're upgrading an access control system to an electric strike, you must ensure that your new system is compatible. You will also have to ensure that the strike is properly connected to your access control system and set up to operate in a safe manner.

Upgrade your strike plates with heavy duty strike plates to block the entry of unauthorized persons. These plates can be fitted with up to six screws of three inches instead of two screws of three-fourths inches. These screws are longer, making it more difficult for someone to break the frame and reach inside to turn the thumb turn part of a single deadbolt cylinder.