• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up Windows and Doors Before a Storm Hits

boarding up doors up your doors and windows before an event can give you the protection you need against damage. You'll require a few items to do this.

Measure the height and width of the window, including the frame (not the trim or boarding up windows and doors the masonry around the window). Note these measurements so you don't forget them.

Preparation

It is recommended to secure doors and windows before the storm or another natural disasters strike. This will reduce property damage and reduce the chance of a fatality. It requires a lot of planning to put up windows. You must purchase and measure plywood boards, and you need to be aware of the specific dimensions of each window. It takes time to cut and install the boards in a proper manner. Fortunately, the process can be simplified by starting the preparations immediately you learn of a possible storm forming in your area. By doing this, you can avoid a stressful last-minute rush and make the process easier for yourself and your staff.

Begin by listening to forecasters service for boarding up windows weather and observing the guidelines of your local government. If you start earlier in the process, you will be able to gather the materials and store them without being overwhelmed by the approaching storm. It is possible that you will require a large amount of plywood to cover your windows, dependent on the severity and imminence of the storm. Use a tape to measure the width and height of each window opening. Make sure you consider the framing or trim around each window, as and any sills with extended extensions if applicable.

Divide the total width and the height of your window by 2 to determine the amount of plywood sheets that you will need. For example, if the width of your window is 16 inches, the thickness of each sheet should be 8 inches. If your exterior is made of wood, drill pilots holes in the plywood sheet so that they align with the window frame below. This will reduce the possibility of splitting when you screw in the screws.

For a window opening that is bigger than what a sheet of plywood can handle cut two sheets that are each half the size of the desired window and set them side-byside on the wall. Cut a piece of 2 by 4 inches (5.1 10.2 cm) 10.2 cm) of lumber to the length the connecting edge between the plywood sheets, and place it on the top of the seam. Then screw 2.25 in (5.7cm) screws into the plywood sheet, and then through the bracing to join the two together.

Materials

To ensure security and safety ensure safety and security, use only materials that are sturdy and won't be damaged or break in high winds. The most common material used to encase windows is plywood, which is cheap, readily available and easy to work with. It is important to select plywood that is specifically designed for exterior use (CDX) for added strength and is free of knots and warping. A sturdier option is storm shutters, also known as hurricane shutters, which are put up over existing windows to provide more protection against glass shattering and inclement weather.

Once you have identified the location of the window openings you can take measurements of the height and width to determine the amount of plywood you will require. Then make use of a power drill to make pilot holes into the plywood sheets at 2-inch intervals around each window. Mark the studs on the wall before attaching the plywood to ensure the boards are secured. If you have wood siding on your home, look for nailheads to determine the stud location. In other cases, you can search for stud locations using your drill. Be sure to insert the screws into the framing, not the sheathing or trim; A plywood panel that is fastened to these materials could be an hazard during strong winds.

If your window is too large for one sheet of plywood, you could cut two pieces of plywood each half the size and join them using two by four inches of lumber. Label each sheet of plywood so you know what window it will cover.

Make sure you use corrosion-resistant screws that are long enough to penetrate the sheathing and the studs that will be used to join the plywood panels to the wall. Make sure to insert the screws into the studs in a way that they are half as deep as the thickness of the plywood however, be cautious not to go too deep and harm the underlying structure of your house.

It is also worth considering installing polycarbonate security glass like DefenseLite on your windows that are primary. These transparent shields are secured to the existing glass and safeguard your windows and doors. They are virtually indestructible and deter criminals from gaining entry into your home.

Installation

If you live in or plan to move to a place which is susceptible to hurricanes and are worried about the storm you should consider boarding up all your doors and windows. It's a project that can be accomplished quickly and efficiently but only if make the effort to measure and cut, then label your plywood before the storm comes.

You'll require additional tools, including drills, saws (or an hammer that has nails if you do not have the power tool), a level, gloves, and safety glasses. It is a good idea to coat the plywood with sealant, as well, to make it waterproof.

Start by measuring the height and width of each window's opening, and then cutting the plywood sheets so that they fit inside the frames, with an overlap of 4 inches on all sides. It's best to do this on-site, as it allows you to control the exact dimensions of the plywood.

Cut the boards to the size you want with a track or circular saw. Once they're installed you'll need to sand them down completely. them. Once you've got your boards place, screw three-inch stainless steel hanger bolts into the framing studs that surround each window. Use washers to secure each bolt as well as wing nuts. Make sure that each screw is inserted at least 2 inches deep into the studs to ensure that the 24 hour boarding up service near me is strong enough to withstand high winds.

If you're building with concrete block, you can instead attach the plywood to the building using galvanized pan-head screws driven through the edges that overlap of each panel to form masonry blocks or cinder blocks. It is also necessary to drill pilot holes in the masonry before screwing corrosion resistant screws into the holes. The project could take about three hours per period. It is important to begin the project as soon when an alert for hurricanes has been issued. This will give you ample time to finish the job before the storm arrives.

Maintenance

You should be prepared to secure your windows and doors before the onset of a severe storm. This will help you to avoid costly repairs and safeguard your home from further damage caused by rain, wind flying objects, and other causes.

The proper materials can make boarding up service near me up easier and quicker. The key is to precisely determine the dimensions of each window you need to cover. This will ensure the OSB or plywood fits well and will not be able to slide off easily. If you're using plywood, ensure that you are using exterior-grade sheets, and consider adding an extra layer of protection.

Mark the places where the screws will need to be placed into the board after you have taken measurements of the OSB or plywood. Make use of a drill to drill holes at intervals of 12 inches into the plywood. This allows you to securely attach the boards to hanger bolts during an 24 hour emergency boarding up or in the event of a disaster. After the storm has passed and you've received the all-clear from local authorities, remove the hanger bolts, but keep them in place for any future emergencies.

The next step is to place the plywood panels over the windows. Be prepared to work in pairs. If you're using plywood be sure to sand the edges of the piece to smooth them so they don't scratch paint or cut. Then, nail the plywood to the frame with screws that are corrosion-resistant that fit into the pilot holes. If your home has vinyl shingles on it, attach the plywood directly to the shingles and not to the wood framing.

A window that has been boarded up may be used to deter burglars. The burglars will be more likely to target a structure with a damaged window or one that's not locked. They're also more likely to enter an establishment that's been closed as opposed to one that's not. If you're a retailer owner, this is a matter you must take seriously.